Search Results for the EPA National Library Catalog

Items Found: 130

Showing: Items 1 - 50

Your Search: (SUBJECT=Valves)

 
 
 

1 2 3 NEXT
Select Item Title Year Published
1995 protocol for equipment leak emission estimates / 1995
1997 variable valve actuation and power boost. 1997
1998 variable valve actuation and power boost. 1998
ANSI/AWWA C223-13 : fabricated steel and stainless steel tapping sleeves / 2013
Approaches to risk assessment for multiple chemical exposures / 1984
Approaches to risk assessment for multiple chemical exposures / 1984
AWWA standard for air-release, air-vacuum, and combination air valves for waterworks service. 1992
AWWA standard for ball valves, 6 in. through 48 in. (150 mm through 1200 mm). 1992
AWWA standard for double check valve backflow-prevention assembly. 1998
AWWA standard for double check valve backflow-prevention assembly. 1989
AWWA standard for metal-seated gate valves for water supply service / 1993
AWWA standard for open-channel, fabricated-metal slide gates. 1997
AWWA standard for power-actuating devices for valves and sluice gates 1994
AWWA standard for protective epoxy interior coatings for valves and hydrants. 1990
AWWA standard for reduced-pressure principle backflow-prevention assembly. 1989
AWWA standard for reduced-pressure principle backflow-prevention assembly. 1998
AWWA standard for resilient-seated gate valves for water supply service. 1994
AWWA standard for rubber-seated butterfly valves. 1994
AWWA standard for swing-check valves for waterworks service, 2 in. (50 mm) through 24 in. (600 mm) NPS. 1993
AWWA standard for underground service line valves and fittings. 1989
Benzene equipment leak inspection manual / 1990
Benzene equipment leak inspection manual / 1990
Blast furnace slips and accompanying emissions as an air pollution source / 1976
Characterization of Leaded Fuel Needs and Use Task 2 Topical Report. 1985
Condition assessment of water main appurtenances / 2012
Construction Details of Isokinetic Source-Sampling Equipment. 1971
Control of NO(x) Emissions from Mobile Sources. 1972
CRC pilot program to investigate the effect on driveability of intake valve deposits and variations in fuel volatility : (CRC project no. CM-118-92) / 1993
Criteria for valve location and system reliability 2006
Design and analysis of piping and components, 1990 : including valve testing and applications : presented at the 1990 Pressure Vessels and Piping Conference, Nashville, Tennessee, June 17-21, 1990 / 1990
Detailed Design: Rankine-Cycle Power System With Organic-Based Working Fluid and Reciprocating Expander for Automobile Propulsion. Volume II. Appendices. 1972
Development of technical specifications for standard gas-diluent mixtures for use in measurement of mobile source emissions / 1974
Distribution valves : selection, installation, field testing, and maintenance. 1996
Don't Wait Until 1998: Spill, Overfill, and Corrosion Protection for Underground Storage Tanks Regulated in New Jersey. 1995
Don't Wait Until 1998: Spill, Overfill, and Corrosion Protection for Underground Storage Tanks. 1994
Emission testing of 1974 Pontiac V-8 with defective thermal vacuum valves. 1976
Emissions and fuel economy of a vehicle equipped with the Eaton valve selector / 1980
Emissions and fuel economy of Turbo-Carb : a retrofit device / 1982
EPA evaluation of the "Auto-Miser" device / 1980
EPA evaluation of the "Environmental Fuel Saver" device / 1980
EPA evaluation of the Atomized Vapor Injector device under section 511 of the Motor Vehicle Information and Cost Savings Act / 1983
EPA evaluation of the Cyclone-Z device under Section 511 of the Motor Vehicle Information and Cost Savings Act / 1983
EPA evaluation of the Dresser Economizer device under Section 511 of the Motor Vehicle Information and Cost Savings Act / 1982
EPA evaluation of the dynamix device under Section 511 of the motor vehicle information and cost savings act / 1982
EPA evaluation of the Energy Gas Saver under section 511 of the Motor Vehicle Information and Cost Savings Act / 1982
EPA evaluation of the freedom products hot tip device under Section 511 of the Motor Vehicle Information and Cost Savings Act / 1982
EPA evaluation of the FUEL-MAX device under section 511 of the Motor Vehicle Information and Cost Savings Act / 1981
EPA evaluation of the gas saving and emission control improvement device under Section 511 of the Motor Vehicle Information and Cost Savings Act / 1983
EPA evaluation of the Malpassi Filter King device under Section 511 of the Motor Vehicle Information and Cost Savings Act / 1983
EPA evaluation of the Optimizer device under section 511 of the Motor Vehicle Information and Cost Savings Act / 1983
1 2 3 NEXT

Save, Print or Email Selected Records