Vibratory Residual Stress Relief and Modifications in Metals to Conserve Resources and Prevent PollutionEPA Grant Number: R828737C004
Subproject: this is subproject number 004 , established and managed by the Center Director under grant R830420
(EPA does not fund or establish subprojects; EPA awards and manages the overall grant for this center).
Center: Center for Environmental and Energy Research (CEER)
Center Director: Earl, David A.
Title: Vibratory Residual Stress Relief and Modifications in Metals to Conserve Resources and Prevent Pollution
Investigators: Hahn, William F.
Institution: Alfred University
EPA Project Officer: Klieforth, Barbara I
Project Period: September 1, 2000 through August 31, 2002
RFA: Targeted Research Center (2000) Recipients Lists
Research Category: Targeted Research
Many manufacturing processes use large amounts of energy in order to make useful products. One such process is the thermal stress relief (TSR) process that is widely used to reduce/modify the internal or residual stresses in parts that are introduced by other manufacturing procedures such as fabrication, machining, or assembly. The TSR process is typically done in large furnaces and is heated by the combustion of fossil fuels. The large consumption of energy, the thermal influence, and air pollution affects on the environment are the biggest concerns of this process. As an alternative to the TSR, Vibratory Stress Relief (VSR) has the advantages of low energy consumption and dramatic reduction of pollution to the environment.
The residual stresses in parts will cause them to distort either during the manufacturing process and/or later during the useful life of the part. The widely used traditional process of thermal stress relief involves raising the temperature of the part under carefully controlled conditions several 100 degrees, holding at the high temperature until the bulk of the stresses have been removed, and then slowly cooling the part in order to prevent introducing new residual stresses. For some parts, this may have to be done several times during the manufacturing process. Thermal heat treatment of stress relief always results in some loss of strength in the part, some distortion during the process, and oxidation of the surface of the part. Vibratory stress modification is an alternative method for altering and/or reducing residual stresses in parts so that they do not distort during subsequent manufacturing processes and during the life of the part. Vibratory stress relief is accomplished by vibrating the part at a particular frequency and amplitude for a short period of time thereby using a minute amount of energy and generating a minute amount of pollution compared to the traditional heat treatment process.
To implement an alternative process, a thorough understanding of how it works and why it works must be developed. Without this understanding, it is difficult for engineers and manufacturing managers to determine when, where, and how the vibratory stress relief process can be effectively applied.
The objective of this research is to develop an analytical model using Finite Element techniques to show how vibration alters the residual stress in a part in a beneficial way. The results of the analytical modeling demonstrated the reduction in residual stress in a particular part due to vibration.
A cantilever beam model was developed in ANSYS, commercial finite element analysis software, for VSR analysis. Due to the symmetry design of the cantilever beam specimen, only half of the beam requires modeling with ANSYS. A two-dimensional model was considered because the stress introduced across the thickness of the beam was assumed uniform.
To model plastic deformation, elastic-plastic material was employed in the ANSYS model database. Aluminum 6061-T6 was selected as the material for the model. For finite element analysis, the model was meshed with linear, four-node, quadrilateral elements.
To simulate the vibratory stress relief, residual stress was first introduced into the model by applying and releasing an external force on the tip of the beam. Static non-linear analysis was conducted to introduce the residual stress and calculate the resulting internal stress distribution. The relationship between the external load and tip deflection was also obtained as information for later determining the vibration amplitude.
The controlling parameters for the vibratory stress relief considered were existing residual stress level, driven frequency, and excitation amplitude. These parameters were obtained from static nonlinear, modal, and harmonic analyses.
To investigate the frequency rangewhere vibration works to relieve residual stress in parts and the driven frequencies that maximize the relief of residual stress in parts, four cases were run to compare the effect of resonance frequency and sub-resonance frequency on VSR.
The results show that the frequency producing the greatest stress relief occurs at the resonant peak (natural frequency). The reduction of residual stress after resonant vibratory treatment can attain 97 percent. Sub-resonant VSR treatments get less or no residual stress relief, depending on the frequency level applied.
Another variable investigated for VSR was the excitation amplitude to observe the effect of excitation displacement amplitude on VSR. The results show that larger excitation amplitude will produce greater stress relief.
Initial residual stress level in parts was also investigated to see its effect on VSR. Two cases were compared with different initial residual stress in the sample. The comparison results show that the part that has less initial residual stress level will get greater stress relief under the same excitation frequency and displacement amplitude.
Publications and Presentations:Publications have been submitted on this subproject: View all 1 publications for this subproject | View all 34 publications for this center
Supplemental Keywords:thermal stress relief (TSR), vibratory stress relief (VSR), residual stress, analytical modeling, finite element analysis, ANSYS, plastic deformation, static non-linear analysis, RFA, Scientific Discipline, INTERNATIONAL COOPERATION, TREATMENT/CONTROL, Sustainable Industry/Business, POLLUTION PREVENTION, Sustainable Environment, Energy, Technology, Technology for Sustainable Environment, Chemistry and Materials Science, Environmental Engineering, energy conservation, cleaner production, environmentally conscious manufacturing, clean technologies, green design, vibratory visual stress relief, alternative materials, thermal stress relief alternative
Progress and Final Reports:
Main Center Abstract and Reports:R830420 Center for Environmental and Energy Research (CEER)
Subprojects under this Center: (EPA does not fund or establish subprojects; EPA awards and manages the overall grant for this center).
R828737C001 Environmental Impact of Fuel Cell Power Generation Systems
R828737C002 Regional Economic and Material Flows
R828737C003 Visualizing Growth and Sustainability of Water Resources
R828737C004 Vibratory Residual Stress Relief and Modifications in Metals to Conserve Resources and Prevent Pollution
R828737C005 Detecting and Quantifying the Evolution of Hazardous Air Pollutants Produced During High Temperature Manufacturing: A Focus on Batching of Nitrate Containing Glasses
R828737C006 Sulfate and Nitrate Dynamics in the Canacadea Watershed
R828737C007 Variations in Subsurface Denitrifying and Sulfate-Reducing Microbial Populations as a Result of Acid Precipitation
R828737C008 Recycling Glass-Reinforced Thermoset Polymer Composite Materials
R828737C009 Correlating Clay Mineralogy with Performance: Reducing Manufacturing Waste Through Improved Understanding
R830420C001 Accelerated Hydrogen Diffusion Through Glass Microspheres: An Enabling Technology for a Hydrogen Economy
R830420C002 Utilization of Paper Mill Waste in Ceramic Products
R830420C003 Development of Passive Humidity-Control Materials
R830420C004 Microarray System for Contaminated Water Analysis
R830420C005 Material and Environmental Sustainability in Ceramic Processing
R830420C006 Interaction of Sealing Glasses with Metallic Interconnects in Solid Oxide and Polymer Fuel Cells
R830420C007 Preparation of Ceramic Glaze Waste for Recycling using Froth Flotation
R830420C008 Elimination of Lead from Ceramic Glazes by Refractive Index Tailoring
R830420C010 Nanostructured C6B: A Novel Boron Rich Carbon for H2 Storage